How to Clean Dr.Brown Bottle Warmer

Thinking about cleaning your Dr. Brown bottle warmer? But the question is, how to clean dr.brown bottle warmer? Where do you even start?

It might seem difficult but bear with us here. We will explain how you can get that job done without going through any hassle. Remember your Dr.Brown bottle warmer has a detachable reservoir and warming basket. Moreover, it’s dishwasher safe.

So, cleaning the bottle warmer shouldn’t be that tough, right? And cleaning the bottle warmer regularly will make sure that it’s working properly every single time you use it.

Without any further ado, let’s get started.

How to Clean Dr.Brown Bottle Warmer

How to Clean Dr.Brown Bottle Warmer

Down below you’ll find the steps that you need to follow in order to get your Dr.Brown bottle warmer cleaned:

  • Unplug it and let it cool before you get started

This might sound like a no-brainer. You should never try to clean the bottle warmer while it’s plugged into a power source. And if you have recently used this appliance, then you have to let it cool down for at least half an hour before cleaning it.

As you’re probably aware, a bottle warmer utilizes heated steam to warm the water bottle. So, the inside will be extremely hot after you’ve used it.

And it goes without saying, you should take all the necessary safety precautions before starting.

  • Take out the water reservoir

There is a transparent water reservoir located on the right side of the bottle warmer. You have to remove it by pulling it in the upward direction. Then pour the water out of it.

After that fill it up with soapy, warm water and leave it be for a few minutes. Make sure you don’t use any harsh soap while cleaning it, as that could cause damage to the reservoir.   

  • Remove the water from the heating compartment

Take the bottle warmer and hold it over the sink and remove the cover. Then tilt it over in order to empty its heating chamber. Ensure that no water remains inside the bottle warmer.

  • Wash the basket inside the dishwasher

Put the basket (a plastic container that holds the bottle) of the bottle warmer on the rack of your dishwasher. And clean it while washing your dishes.

In case, you don’t want to wash it using the dishwasher, you always have the option of cleaning it by hand.

After you’re done cleaning it, let it dry for some time.

  • Wash the Bottle Warmer

Now it’s time to wipe the bottle warmer using a sponge or rag that has been dipped into soapy water. Mix just a little bit of detergent or a few drops of dish soap with some warm water. Then mix it and dip the sponge into it.

After that, gently wipe down both the inside and outside parts of the bottle warmer.

  • Put some rice and water into the reservoir

After you’ve soaked the reservoir into soapy water for a few minutes, remove the soapy water out of it. Then pour one tablespoon of rice and one tablespoon of water into it. Use a funnel if you have to.

  • Vigorously Shake the Reservoir

Place your index finger on the mouth of the reservoir and then shake it back and forth. Do it at a fast pace so that the rice gets to hit each and every part of the surface inside the reservoir.

This is done in order to remove the soapy residue from the reservoir.

  • Rinse the bottle warmer’s reservoir

First, you have to pour the rice and water out of the reservoir. After that, rinse that container multiple times using cold water. Partially fill the reservoir with water and then shake it to clean it properly.

If you still see suds inside the reservoir, then repeat steps 6-8 one more time.

  • Air Dry Everything

Now that you’re done cleaning the components of your Dr.Brown bottle warmer place them on top of a towel and let them dry for 1-2 hours.

Actually you can use the reservoir even before it’s completely dry, as you’re going to put water into it again anyway. But the outside components have to be totally dried before use.

Place the reservoir back into its position and reattach it to the right side of the bottle warmer. Then place the basket into its chamber.

You should clean your Dr.Brown bottle warmer at least once a week. That will prevent it from releasing any bad odor.

Descale the Bottle Warmer

If you want the optimum performance from your bottle warmer, you have to descale it. If you don’t descale it regularly, then it could cause residual to build upon the bottle warmer’s heating element.

The steps for descaling the Dr.Brown bottle warmer is given below:

  • If your bottle warmer’s not working, that would mean that limescale has built-up inside the appliance. You have to run vinegar through it in order to break that buildup down.
  • Just like before, you have to unplug the device and let it cool for half an hour.
  • Take the water out of the reservoir as well as the heating chamber by tilting them on top of your sink.
  • Then pour 50ml white vinegar and 100ml water into the reservoir. Don’t worry; vinegar is a safe and natural substance. It won’t cause any harm to the appliance.
  • Do the same for the reservoir as well. And leave them like this for a few minutes.
  • Then pour the vinegar solution out of the reservoir and the warmer.
  • Plug it back in and test it out.

Final Thoughts

So, did you find our guide about how to clean dr.brown bottle warmer interesting? If you’re confused about anything, you can always refer back to the instruction manual of your bottle warmer.

Remember to clean your bottle warmer once every four weeks. And don’t forget to rescale the bottle warmer after cleaning it.

Jessica Alba

Jessica Alba is passionate about home improvement and design. As a child, she grew up helping her dad renovate their childhood home. Many of her skills came from this experience. Jessica loves DIY projects and sharing her passion for home design with others since she lives in Los Angeles.

Leave a Reply

Your email address will not be published. Required fields are marked *

Recent Posts